Skip to content

Formulation and scale-up

Planning Hot Fill and Pasteurization Checks for Magnesium Drinks

A check plan for hot fill beverage mineral stability: what to measure before and after heat, which controls to run, how to log the process and where the regulatory process requirements sit.

By MagneINNOUpdated 5 min read

The practical answer

Hot fill beverage mineral stability is checked by measuring the same fortified drink and an unfortified control before and after the real heat step, at the planned conditions and at the hottest and longest conditions the line may reach. Measure pH, turbidity, sediment, color, total and dissolved magnesium and sensory character, and log time and temperature for every sample. The process itself, including whether the product is a low-acid, acidified or juice product, is set by the qualified process authority and the applicable regulations, not by the magnesium result. [1–4]

Know which process rules apply before testing

A drink with a finished equilibrium pH above 4.6 and water activity above 0.85 is a low-acid food under 21 CFR 113.3, unless an exception applies. An acidified food has to reach and keep a finished equilibrium pH of 4.6 or lower within the time set in the scheduled process, and part 114 excludes carbonated beverages and foods stored, distributed and retailed under refrigeration. Juice processors not subject to parts 113 or 114 need HACCP control measures that achieve at least a 5-log reduction in the pertinent microorganism, with a stated exemption for a single thermal step that makes the juice shelf-stable. [1–3]

Those rules decide the process. The magnesium checks below decide whether the formula survives that process with the appearance, pH and content the product needs.

Measure before and after the real heat step

Prepare one batch of the fortified drink and one of the unfortified base. Split each into an unheated reference and processed samples. Run the processed samples through the planned profile on the pilot equipment, or the closest bench simulation you can document, and also at the hottest and longest conditions the line could reach during a deviation. Fill into the commercial container type, because heat transfer and cooling depend on it.

For each sample, record pH, turbidity on a stated instrument, visible sediment, color, total magnesium and, if the team needs it, magnesium in the liquid after a defined separation step. Taste the processed samples against the unheated reference. A change that appears in both the fortified and the unfortified samples belongs to the base or the process, not to the magnesium ingredient.

Log the process the way production will

Record product temperature at the start and end of the hold, hold time, fill temperature, any container inversion or hold step, cooling method and time to reach the final temperature. A heat check is only comparable with production if the time and temperature history is comparable. Keep the logs with the sample identity so a later result can be traced to its exact profile.

Measure pH with a calibrated meter at a stated temperature. For acidified foods, part 114 requires the finished equilibrium pH to be measured potentiometrically when it is above 4.0, and in-process titration or colorimetric results have to be related to that measurement. Even when part 114 does not apply, the same discipline makes the pH data usable. [5]

Decide what counts as a failure in advance

Write the acceptance criteria before the trial: the allowed pH change, the turbidity limit relative to the unfortified base, whether any sediment is acceptable, the allowed difference in total magnesium between unheated and processed samples beyond method variability, and the sensory comparison to be used. For a conventional beverage, the magnesium declared on the label is a Class I nutrient, so the formula target has to allow for any loss the checks reveal. [6]

If the processed samples fail, change one factor at a time, such as the order of addition, the acid system or the magnesium loading, and repeat the same check. Raising the magnesium input to cover an unexplained loss hides the cause rather than fixing it.

Carry the result into the stability study

A passing heat check supports moving to a shelf-life study in the commercial package. It does not set a shelf life. Use the processed samples, not the unheated ones, as the time-zero reference for that study, and schedule the pulls with a fixed calendar so each time point is tested under the same conditions.

Common questions

Does a magnesium ingredient change the process requirements for a drink?

The process requirements depend on the product classification, pH, water activity and process under the applicable regulations, set with a qualified process authority. A magnesium heat check does not change them; it shows whether the formula tolerates the process.

Is a heat check in a beaker enough?

It is a useful first screen. The decision should rest on samples processed with the real or a documented simulated time and temperature profile and filled into the commercial container type.

Sources & further reading

  1. 21 CFR 113.3, Thermally processed low-acid foods packaged in hermetically sealed containers: definitions
  2. 21 CFR 114.3, Acidified foods: definitions
  3. 21 CFR 120.24, Juice HACCP process controls
  4. 21 CFR 113.83, Establishing scheduled processes (low-acid foods)
  5. 21 CFR 114.80, Acidified foods: processes and controls
  6. 21 CFR 101.9, Nutrition labeling of food
This guide supports ingredient qualification and formulation planning. It does not establish a clinical dose, certify a finished product, or replace current lot documentation. General references explain the underlying topic; they do not independently verify MagneINNO-specific performance claims.